NXP Semiconductors Controladores de motor con variador Fm+ bus I2C PCA9629

Los controladores de motor con variadorFm +bus I²C PCA9629 de NXP son dispositivos CMOS de baja potencia controlados por bus I²C que ofrecen toda la lógica y control necesarios para controlar un motor con variador de cuatro fases. El PCA9629 está diseñado para utilizarse con controladores externos de alta corriente para controlar las bobinas del motor. Es compatible con tres formatos de control de motor con variador: una fase (control de onda), dos fases y media fase. Además, cuando se utilizan como entradas, cuatro entradas/salidas de propósito general (GPIO) permiten la detección de salida de nivel lógico de módulos de interrupción ópticos y generan una señal de interrupción BAJA activa en el pin INT del PCA9629. Esta característica resulta muy útil en la detección de la posición de inicio del eje del motor o como referencia para los pulsos de pasos. Cuando hay una interrupción, el PCA9629 puede programarse para parar el motor automáticamente o invertir la dirección de rotación del motor.

Output wave train is programmable using control registers. The control registers are programmed via the I²C-bus. Features built into the PCA9629A provide highly flexible control of stepper motor, off-load bus master/micro and significantly reduce I²C-bus traffic. These include control of step size, number of steps per single command, number of actions from 1 to 255 or continuous rotations and direction of rotation. Re-start motor for new speed and operation without waiting for motor stop. A ramp-up on start and/or ramp-down on stop is also provided with re-enable ramp-up or ramp-down to change the ramp rate curve on the fly.

The PCA9629A is available in a 16-pin TSSOP package and is specified over the ‑40°C to +85°C industrial temperature range.

Características

Generate motor coil drive phase sequence signals with four outputs for use with external high current drivers to off-load CPU
Four balanced push-pull type outputs capable of sinking 25mA or sourcing 25mA for glueless connection to external high current drivers needed to drive unipolar stepper motor coils
- Up to 1000pF loads with 100 ns rise and fall times
Built-in 1MHz oscillator requires no external components
Stepper motor drive control logic
One-phase (wave drive), two-phase, and half-step drive format logic level outputs
Programmable step rate: 333.3kpps to 0.3pps with ±3% accuracy
Programmable ramp-up on start and ramp-down to stop
Programmable re-enable ramp-up or ramp-down to change ramp rate curve on the fly
Programmable re-start motor with new speed and operation while motor is still running
Programmable motor action either multiple times (1 to 255) or continuously
Programmable loop delay timer for motor reversal mode
Programmable steps with clockwise and/or counter-clockwise control
Direction control of motor shaft
Interrupt features
- Active LOW open-drain interrupt output
- Programmable watchdog timer with option to generate interrupt, reset device or stop motor
- Programmable motor stop interrupt
- Sensor enabled drive control: linked to interrupt from GPIO pins
- Programmable interrupt Mask Control for input sources
Four stepper motor drive outputs (OUT0 to OUT3)
- Configured to drive stepper motor outputs and capable to read back the last output states when motor is stopped
- Both output phase and state can be changed at any time
- Programmable time-out timer to set all outputs to zeros when motor is stopped
- Configured as general purpose outputs to drive (source/sink) loads up to 25mA
Four general purpose I/Os (P0 to P3)
- Configured to sense logic level outputs from optical interrupter photo transistor circuit
- Programmable filter timer to suppress spike or noise for P0 and P1 inputs
- Configured as outputs to drive (source/sink) LEDs or other loads up to 25mA

Selectable active hold (last state), power on, power off or released states for motor shaft
32-bit step counter to count output steps
4.5V to 5.5V operation
1MHz Fast-mode Plus (Fm+) compatible I²C-bus serial interface with 30mA high drive capability on SDA output for driving high capacitive buses
Active LOW reset (RESET) input pin resets device to power-up default state: can be used to recover from bus stuck condition
All Call address allows programming of more than one device at the same time with the same parameters
16 programmable slave addresses using two address pins
‑40°C to +85°C operation
ESD protection exceeds 2000V HBM per JESD22-A114 and 1000V CDM per JESD22C101
Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100mA
TSSOP16 package